AmericanLongRifles Forums
General discussion => Gun Building => Topic started by: Acer Saccharum on December 07, 2013, 11:57:16 PM
-
This is a trial posting for a tutorial on stabbing and background relieving. Post whatever you feel appropriate for the topic, as I have found that the comments that go along with the thread are full of good ideas. This will eventually be edited and posted in the tutorial section. Thanks, Tom
Draw your sketch on the wood with pencil. Second best tool is a big pink eraser.
(https://i12.photobucket.com/albums/a246/Tom45-70/Contemporary%20guns/Beastie%20build/DSC_2539_zps83d9c64f.jpg) (https://s12.photobucket.com/user/Tom45-70/media/Contemporary%20guns/Beastie%20build/DSC_2539_zps83d9c64f.jpg.html)
Tiny tools note the ends are rounded. The two on the right have flat backs, rounded fronts. The one on the left is rounded on both sides. Same tools in same order in the phot below.
Top row across is the tool plunged straight into the wood.
Second row is the tools plunged and then rocked right to left. This 'rolling' of the point causes the tool to creep along the wood. The flat backed tools can go around a tighter curve, flat toward the inside of the curve.
(https://i12.photobucket.com/albums/a246/Tom45-70/Contemporary%20guns/Beastie%20build/DSC_2571_zps064e57b6.jpg) (https://s12.photobucket.com/user/Tom45-70/media/Contemporary%20guns/Beastie%20build/DSC_2571_zps064e57b6.jpg.html)
Design stabbed in, but not very deeply. As I cut the background away and come up to the stabbed line, the waste wood pops off. If I haven't stabbed deep enough, the waste wood hangs on. So I can take the stab tools and cut a touch deeper wherever I need to.
(https://i12.photobucket.com/albums/a246/Tom45-70/Contemporary%20guns/Beastie%20build/DSC_2568_zps997a6bd0.jpg) (https://s12.photobucket.com/user/Tom45-70/media/Contemporary%20guns/Beastie%20build/DSC_2568_zps997a6bd0.jpg.html)
Sketch completely stabbed. For a few inside and outside radii, I use a gouge that fits the drawing.
(https://i12.photobucket.com/albums/a246/Tom45-70/Contemporary%20guns/Beastie%20build/DSC_2562_zps1adb637a.jpg) (https://s12.photobucket.com/user/Tom45-70/media/Contemporary%20guns/Beastie%20build/DSC_2562_zps1adb637a.jpg.html)
(image of background cutting tools and techniques still needs to be created)
Background is all cut down, and faired back enough so that the surface doesn't look like it's 'diving in'.
(https://i12.photobucket.com/albums/a246/Tom45-70/Contemporary%20guns/Beastie%20build/DSC_2580_zps90bc1671.jpg) (https://s12.photobucket.com/user/Tom45-70/media/Contemporary%20guns/Beastie%20build/DSC_2580_zps90bc1671.jpg.html)
-
Thank You. Could you please explain your tools and methods for leveling off the low area so evenly and smoothly? Dan
-
Thank You. Could you please explain your tools and methods for leveling off the low area so evenly and smoothly? Dan
Yes, Dan, will do. That is one photo I don't have, but will be sure to capture it next piece of backgrounding I do.
-
This will be a very helpful tutorial. Could you also cover incised carving? thanks
-
Tom, when you have all the wood removed from around the design is there still the stabbed in cut along the design, lower into the wood than the surounding area that you carved away? Hope I explained that so you know what I was wondering about. Smylee
-
This will be a very helpful tutorial. Could you also cover incised carving? thanks
This is an incised carving technique.
-
I would also like to see some detail on the tools. How do you shape them?
-
At some point, I would cover incised, once I feel I know enough about it.
Eric Kettenburg is one master of that technique.
See some incised examples of work on his website at:
http://www.erickettenburg.com/Site/1750s_Rifle.html
http://www.erickettenburg.com/Site/John_Rupp.html#5
http://www.erickettenburg.com/Site/More_Allentown_Rifles.html#2
-
Acer, your presentation so far has been an eye opener for me. Without knowing too much about it I had previously felt that stabbing in was a more primitive approach than using a veiner. Now that I've seen it in action, so to speak, I'm just seeing a different way to the same end. I shall be interested to see which approach I end up favouring.
Could you include the whole tools in a future photo? I'd like to see how small they are and what type of handle you used.
I'm also curious about the same point as smylee grouch. I think I can actually see little cut marks around the figure after the background has been relieved. I realise they will close up quite a bit after a wetting, such as staining, but wont the cut fibres still tend to pick up extra stain and produce a dark outline?
-
The stabbed lines will indeed close up during the finishing process, and they will also show up as dark lines, having absorbed more stain and finish. This can be an asset or an annoyance, depending on the style of carving you're doing. I think for shallow-carved rifle work, the dark line enhances the outline of the carving, and will help make it look more dimensional than it really is.
-
DaveP, for years I was totally resistant to stabbing, because I like the freedom of the parting tool for tweaking the design.
So with stabbing, you need to do your tweaking with the pencil and eraser. Once you've stabbed that line in, you're committed to the design.
-
Acer,
We all look forward to your tutorial. (You are a great teacher!)
The guys may also want to see Gary Brumfield's powerpoint slides on a similar topic.
[oops!. Let me try again. Here's another link. I think this will take you to Gary' own opening link.]
http://flintriflesmith.com/ToolsandTechniques/tools_and_techniques.htm
Whet
-
Whet, I'll include that link in the tutorial, thanks!
-
I've seen Mr. Brumfield's powerpoint slides before and they are an aid, but what's really missing from just about everything I've been able to find in tutorials is the sculpting.
You can find many sources of the design outlined, but what really makes the carving is the minute sculpting that lends the depth to it all.
-
This particular rifle is FLAT carved, with some incised. At least that's the concept at this point.
Here's a little tutorial I did years ago about scuplted carving: http://americanlongrifles.org/forum/index.php?topic=12.0
It's a bit dated, but I hope you find it helpful.
Tom
Time to think about 18the Century Artisan's Show, eh.
-
I would also like to see some detail on the tools. How do you shape them?
Acer,
As David suggested, I think some detail on the tools (what they're made from, how you made them, size of the tips, etc.) would be extremely helpful since many of us will have to make the tools before we attempt this technique. I'm really looking forward to your finished tutorial and taking a crack at this. Thanks.
Mole Eyes
-
Tool description in the tutorial:
I make a lot of these tools, designing what I think might work really well, only to find that they aren't what I was hoping. Other tools turn out to be a slam-dunk, and those I want to emulate on the tutorial.
So much of this hand tool business relates to the individual hand size, strength, method of use.
Long story short, the tool dimensions may be useful to some people, and not to others.
As always, look at all the info, and pick out what works for you.
-
A few thoughts that might be worth mentioning... The most common method for outlining carving using a stab in approach involves using flats and gouges of the appropriate shape. There are trade-offs to everything and that's the case here. Using these gouges usually requires a fairly extensive set of tools. This involves more outlay of money and there are also more tools to maintain. The good aspects of using gouges is that very clean curves can be produced and there is less chance of deviations since a larger length is produced from one stab-in as compared to the tools shown here. The tools Acer has shown are very versatile, cheap and can obviously produce good results, however.
Jim
-
Thanks for that perspective, Jim.
I tried some of what you speak with gouges of appropriate curvature. I have a pretty good selection of radii, twenty five tools ranging from 1/16" radius to about 1" radius, but sadly I found that most of my tools had too deep a gouge. For this technique to be successful, I need gouges with only a partial 'U'. I need almost a whole new set, if I were to go this route.
For the professional furniture carver, the big tool set would be a real time saver. For the occasional gun carver, such as myself, that investment is not practical.
-
I just did a quick count and I use about twelve different gouges on a regular basis when carving a gun stock. So, you're looking at an investment of around $400. But it doesn't take too many guns to pay for this when looking at added efficiency and the consistent good results. So, I agree that for the person who builds just a few guns and isn't looking to make money, this may not be the best approach, but for others, it very well may be. When you look at the time involved, and selling price of a good longrifle this is nothing, especially spread over many rifles.
-
If anyone should be interested, here's a list of the gouges I use most often and would pretty much be fine for the stab-in technique in carving on just about any longrifle.
2/3
2/5
2/8
3/3
3/5
3/8
5/3
5/5
5/8
7/4
7/6
8/2
8/3
8/4
I have a few odd tools I've made up too. Some with a pronounced nose for ending a scroll or making chip cuts etc. I will also add that these can be sharpened wit a bit of a rounded face or nose to make each of the tools a little more versatile. There might occasionally be a small spot where nothing seems to fit and I find a knife works well in these cases.
One thing worth mentioning is that these tools won't necessarily make good carving. It's just like engraving with pneumatics etc. Design is super important and execution needs to be adequate as well.
So, my view is this option might be appropriate for some. It's a technique perfectly at home for longrifle carving and not just restricted to furniture carving etc.
-
Jim:
In your gouge list is the first number the width in millimeters and the second the sweep number? Or is it the reverse? Or am I way off?
Thanks,
Jay
-
Jim:
In your gouge list is the first number the width in millimeters and the second the sweep number? Or is it the reverse? Or am I way off?
Thanks,
Jay
First number is the sweep and second is width in mm. For example 2/3 is a #2 sweep and has a width of 3mm. Sorry I didn't clarify previously.
Thanks,
Jim
-
I think the gouges I have are way too wide for the sweep.
-
Jim, Thanks for posting your list. I have several of those that I use often.
I have a 9/2, 9/3 and 9/4 they all sweep a bit too far. The 8/2 , 8/3 and 8/4 you list would be better for stabbing.
You helped reinforce my thoughts on my tools.
-
Jim, I realized tonight the difference between straight-in stabbing tools that you list, and the tools I'm using, which I will call 'roll-stamping'. The tools are pushed into the wood with hand pressure and then rocked along the path. Each plunge 'n rock moves a larger tool along the path about 1/16", and the smaller tools might only travel 1/32 at the most. I'll post some illustrative photos when I make them.
-
Jim:
In your gouge list is the first number the width in millimeters and the second the sweep number? Or is it the reverse? Or am I way off?
Thanks,
Jay
First number is the sweep and second is width in mm. For example 2/3 is a #2 sweep and has a width of 3mm. Sorry I didn't clarify previously.
Thanks,
Jim
Thanks Jim. that helps a lot.
-
Jim, I realized tonight the difference between straight-in stabbing tools that you list, and the tools I'm using, which I will call 'roll-stamping'. The tools are pushed into the wood with hand pressure and then rocked along the path. Each plunge 'n rock moves a larger tool along the path about 1/16", and the smaller tools might only travel 1/32 at the most. I'll post some illustrative photos when I make them.
Hey Tom. I've used the types of tools you've shown and understand the technique of rolling and advancing them. I actually took a carving class with Gary Brumfield some time ago where he promoted their use. When using gouges I actually use a similar technique in cutting and advancing the tool. For longer cuts, I push the tool in and then generally advance it by rocking against the thumb of my off hand. This lifts the forward corner and advances the tool. I then push in again. I advance around half of the tool width, maybe more maybe less as I don't really pay attention, but just do it.
-
Push tool in, and then roll tool along path. One can start with a shallow cut, and deepen on subsequent passes. When you're removing background, and you find that the stab cuts weren't deep enough, you can cut down a touch deeper in the original path with no ill consequences.
Each little stab and roll advances the tool a little further along the line.
(https://i12.photobucket.com/albums/a246/Tom45-70/Contemporary%20guns/Beastie%20build/Roll-stab_zps2f6cb96d.jpg) (https://s12.photobucket.com/user/Tom45-70/media/Contemporary%20guns/Beastie%20build/Roll-stab_zps2f6cb96d.jpg.html)
-
Acer; where you get the stabbing in tools? would like to get em
-
Yip, they are home made. I'll outline their construction and some pix and instructions when I do the tutorial.
See the photo with block of wood with the tool tips plunged in? The whole tool, handle and all, is about 3". The little engraver's mushroom handles work nicely.
-
Good demonstration photograph Tom, very graphic and expressive of the technique, looks like you are an Ace in Photoshop also. Can't wait for your full tutorial to be published.
dp
-
Most of the photos are untouched.
Only zucchinis are photoshopped into unlikely situations. That takes the zuch from funny to hilarious... right? You with me on this?
-
Only zucchinis are photoshopped into unlikely situations. That takes the zuch from funny to hilarious... right? You with me on this?
I'm with you, Tom.
/mm
(https://americanlongrifles.org/forum/proxy.php?request=http%3A%2F%2Fi312.photobucket.com%2Falbums%2Fll345%2Fmikemeteor%2FStuff%2Flewisclarkz_zpsb739baf5.jpg&hash=7a2fbc50865ef0a987a92c800ffa635ca5003020) (http://s312.photobucket.com/user/mikemeteor/media/Stuff/lewisclarkz_zpsb739baf5.jpg.html)
-
I'm with you, Tom.
/mm
(https://americanlongrifles.org/forum/proxy.php?request=http%3A%2F%2Fi312.photobucket.com%2Falbums%2Fll345%2Fmikemeteor%2FStuff%2Flewisclarkz_zpsb739baf5.jpg&hash=7a2fbc50865ef0a987a92c800ffa635ca5003020) (http://s312.photobucket.com/user/mikemeteor/media/Stuff/lewisclarkz_zpsb739baf5.jpg.html)
That picture needs to be squashed :-\
-
I am DYING, oh, I can't believe it.
See how a little zuch goes from mundane to hilarious? Meteor totally gets it.