Author Topic: My Rifling Bench (Read 34516 times)

runastav · « **Reply #25 on:** February 12, 2015, 09:11:49 PM »

Hi Blackpowder Friends!
Rolf and I got 2 smoothbore barrels from Charles Burton, one Cal 58" for Rolf and a Cal 40" for me

The barrels are very nice, and now my subteenager friend Alf Jostein and me have rifle the cal 40. Rifling is fun if you have a subteenager as power hehe

We find the small caliber more diffiqult than bigger, and some problem there was. But the end result was not bad the rifle depth is ca 005". I think I will build a East Tennessee Squirrel Rifle like Bookie says

barrel lenght is 44"
Runar

Alf Jostein stiring, hmmmm ok he think

And me stiring hmmm ok me think

flinchrocket · « **Reply #26 on:** February 13, 2015, 06:55:31 AM »

Runastav, Does your Burton barrel have the .003 tapered bore?

runastav · « **Reply #27 on:** February 13, 2015, 02:40:32 PM »

Hi all!
flinchrocket-Yes it has tapered bore says Charles Burton

Runar

flinchrocket · « **Reply #28 on:** February 13, 2015, 07:37:52 PM »

Nice job Runastav. Make a good ekorn / spider killer !

multifasciatus · « **Reply #29 on:** February 14, 2015, 01:34:26 AM »

:)Land Ahoy!!
Looking good Runar!

Aj

Steve Bookout · « **Reply #30 on:** February 15, 2015, 08:16:02 AM »

Hei Runar. Are you going to make the breech plug & tang for this project?

kaintuck · « **Reply #31 on:** February 15, 2015, 05:15:58 PM »

Thank you for sharing....sounds like the start of some great rifles!
Marc n tomtom

runastav · « **Reply #32 on:** February 15, 2015, 06:49:14 PM »

Hi All! and thank you!
Bookie, yes I will make one it must have looong tang?
Runar

Jeger Justnes · « **Reply #33 on:** February 20, 2015, 11:57:56 PM »

Neat little hole in that barrel, runastav. Give my regards to Alf. A man with a decent momentum for pulling those grooves ;-)

runastav · « **Reply #34 on:** April 02, 2015, 05:28:06 PM »

Hi all Blackpowderfriends!
Thank you JJ. My friend Rolf came over and we rifle his Charles Burton barrel, cal 58 and loooong ca 48-3/4"

The cutter bit on this one use 7 teeths and Rolf made ca 1000 cuts and we use 18 papershims.
Runar
Rolf in work

Rolf chek the result, hmmmm nice

Me chek hmmmm nice

Daryl · « **Reply #35 on:** April 02, 2015, 06:23:59 PM »

Well done, Runar and Rolf. the rifling in the .58 looks to me to be about .010". Nice and sharp, grooves slightly wide than the lands.

smylee grouch · « **Reply #36 on:** April 02, 2015, 07:48:10 PM »

Those barrels look great from over here. I can hardly wait for the gun building . Thanks for keeping us posted. Happy Easter.

eddillon · « **Reply #37 on:** April 02, 2015, 08:32:46 PM »

Runar, I really enjoy your posts. Nice photos of great work. Rolf, have you started on the matched pair from the board you bought from me?

Dennis Glazener · « **Reply #38 on:** April 02, 2015, 10:28:42 PM »

Quote from: runastav on February 13, 2015, 02:40:32 PM

Hi all!
flinchrocket-Yes it has tapered bore says Charles Burton
Runar

Oh boy, I can see it now, Burton barrels hand rifled in Norway, buy them now while they are hot

Dennis

kaintuck · « **Reply #39 on:** April 02, 2015, 11:51:34 PM »

I have a question....will ALL barrels be the same twist because of the twist on the machine??? so a 54 would have the same twist as a 45, or 35cal?

would that make a difference in shooting???

marc n tomtom

Topknot · « **Reply #40 on:** April 03, 2015, 02:13:33 AM »

Runar, you do excellent work my man.And your photos are killer! Keep up the good work and post plenty of photos along the way.

topknot

runastav · « **Reply #41 on:** August 05, 2016, 05:14:19 PM »

Hi Guys!
My buddy Rolf(Doc) wisit us and we do job for him. First we rifle his Charles Burton barrel cal 54 and 33" lenght.Turned out wery nice, we use 25 paper shims and Rolf work the rifler 1760 times

Runar

Rolf in work

This time I adjust the barrel hight wery careful, and thats the ting

Rolf check his barrel, and is wery satisfied

And me to

Nice ha?

tim crowe · « **Reply #42 on:** August 07, 2016, 12:07:31 AM »

Runar,
You and Rolf need to visit Historic Toad Hall . We will put you to work!

Jeger Justnes · « **Reply #43 on:** August 07, 2016, 12:23:36 PM »

Seems like time and elbow grease well spent, runastav and Rolf :-)

runastav · « **Reply #44 on:** August 09, 2016, 07:01:57 PM »

Hi and thank you guys!
Try to fix the photos but me no good phhuu
Runar

Roger B · « **Reply #45 on:** August 09, 2016, 10:02:01 PM »

I see you are using your wife's toothbrush to clean the cutter. Does she object or have you told her yet?
Roger B.

runastav · « **Reply #46 on:** August 10, 2016, 01:57:00 PM »

Hyshh Roger dont tell her hehehe

Runar

Joe S · « **Reply #47 on:** August 10, 2016, 09:15:46 PM »

Where is Rolf's beard?

Steve Bookout · « **Reply #48 on:** August 10, 2016, 10:08:59 PM »

Hei Runar! The teeth in that barrel look as if they could take a bite right out of your leg (or higher up). Excellent work you've done again and the rifling bench looks like it's wearing in well. The sub-teenager for power is the only way to go. You do need to visit Toad Hall like Tim suggests. Come when he is here and we'll hammer some barrels together.

Rolf · « **Reply #49 on:** August 11, 2016, 06:48:33 PM »

Quote from: Chuck Walla on August 10, 2016, 09:15:46 PM

Where is Rolf's beard?

My wife insists I shave

.

Best regards
Rolf

News:

Author Topic: My Rifling Bench (Read 34516 times)

kaintuck

Jeger Justnes

eddillon

kaintuck

Jeger Justnes

Joe S