Author Topic: Making a "Chiefs Grade" Trade gun Trigger guard *Photos Fixed*  (Read 22595 times)

Offline Curtis

  • Hero Member
  • *****
  • Posts: 2184
  • Missouri
I just finished a trigger guard for a Chief's grade trade gun I am building.  I took a lot of photos along the way so I thought I would share some of the steps I went through while making it, in case anyone is thinking about building a trade gun for the first time.  I also did some engraving on the guard, I am a beginner engraver but early English trade guns didn't usually have the best engraving so it might work out.

I started with a sheet of .80 brass, first I hit it with some cheap white spray paint and sketched on the design:



Then cut it out with a jeweler's saw:





Next I bent the finials 90 degrees at each end of the bow:



Next anneal the bow area with a torch and start the bending process.  I made a poor man's swage block by using a hole saw to cut a hole in a hard scrap of lumber, then sawed the scrap in two in the middle of the hole.  Then the pounding begins:



Annealing again:



Using the "hole" to bend  the bow over:



Then switched to an old pipe section:





I dished out a swaging area on the face of the same board with a gouge, and used it to put some rounding across the bow for strength and appearance:





Then switched to a lead block for fine tuning:





And back to the cutout hole for some adjusting:



These three pics somewhat show the convex shape:







A little adjustment to the finial bends and it is close enough for now:





Now some file work to smooth the dings and add dimension to the finials:





I drew my designs on the brass in pencil and started the engraving process.  For the more complex design on the bow I spritzed a light coat of white paint.  It was more durable than the china white I have.  Here I am using a graver that TOF made for me:



My inspiration for the bow design:



Finished!  Unless I decide to retouch some lines,anyway:









Thanks for looking!


Curtis



« Last Edit: January 30, 2020, 01:56:02 AM by Curtis »
Curtis Allinson
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Sometimes, late at night when I am alone in the inner sanctum of my workshop and no one else can see, I sand things using only my fingers for backing

Offline Angus

  • Full Member
  • ***
  • Posts: 208
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #1 on: July 31, 2015, 12:29:49 PM »
That will make the Chief happy, nice work!

Offline James Wilson Everett

  • Hero Member
  • *****
  • Posts: 1090
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #2 on: July 31, 2015, 01:37:05 PM »
Splendid!  Thanks for posting the photos.

Offline jrb

  • Sr. Member
  • ****
  • Posts: 290
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #3 on: July 31, 2015, 02:33:45 PM »
Thanks for sharing that, Curtis.  As a trade gun nut, i'm really looking forward to seeing your completed gun. :)

Offline Tom Currie

  • Hero Member
  • *****
  • Posts: 1294
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #4 on: July 31, 2015, 02:38:29 PM »
Curtis, Nice job on that guard. Thanks for sharing your process with us.

Offline Marcruger

  • Hero Member
  • *****
  • Posts: 3646
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #5 on: July 31, 2015, 03:08:45 PM »
Good gracious. I love seeing raw material turned into functional art. Well done sir. Marc

brokenflint

  • Guest
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #6 on: July 31, 2015, 03:20:24 PM »
Hey Curtis, nothing at all to be worried about on the engraving job, good work all the way around.

Offline BOB HILL

  • Hero Member
  • *****
  • Posts: 2223
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #7 on: July 31, 2015, 05:31:56 PM »
Well done. Thanks for posting.
Bob
South Carolina Lowcountry

Offline FDR

  • Sr. Member
  • ****
  • Posts: 329
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #8 on: July 31, 2015, 05:32:41 PM »
Well done! Well done!  Thanks for showing us how it was done.  Very educational to us 'want to be".

Offline Daryl

  • Hero Member
  • *****
  • Posts: 14970
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #9 on: July 31, 2015, 05:50:46 PM »
Well done! Well done!  Thanks for showing us how it was done.  Very educational to us 'want to be".

Exactly- well done indeed.
Daryl

"a gun without hammers is like a spaniel without ears" King George V

Offline PPatch

  • Hero Member
  • *****
  • Posts: 2456
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #10 on: July 31, 2015, 06:28:15 PM »
You done good Curtis!  ;D

dave
Dave Parks   /   Quis custodiet ipsos custodes?

Offline Acer Saccharum

  • Administrator
  • Hero Member
  • *
  • Posts: 19311
    • Thomas  A Curran
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #11 on: July 31, 2015, 09:14:40 PM »
Thanks for posting this great photo series!

This make me think 'I can do this!' Good going, Curtis!
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Online Tim Crosby

  • Administrator
  • Hero Member
  • *
  • Posts: 17988
  • AKA TimBuckII
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #12 on: July 31, 2015, 09:45:10 PM »
 Really neat, we'll move it over to the Tutorials in a couple weeks.

  Thanks For Taking The Time to Photograph and post, Tim C.

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13166
    • Mike Brooks Gunmaker
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #13 on: August 01, 2015, 12:22:01 AM »
Nifty I bumble along and make my bends just by hand and eyeball....I like your bending blocks. Next time you might consider concaving the front and rear finials too.
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Offline Curtis

  • Hero Member
  • *****
  • Posts: 2184
  • Missouri
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #14 on: August 01, 2015, 02:38:38 AM »
Thanks for all the positive input guys!  Mike, now that you mentioned that about concaving the finials I remember reading about that on your website.  I couldn't have made the trigger guard on my first trade gun without your tutorial!

Curtis
Curtis Allinson
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Sometimes, late at night when I am alone in the inner sanctum of my workshop and no one else can see, I sand things using only my fingers for backing

Offline hortonstn

  • Hero Member
  • *****
  • Posts: 640
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #15 on: August 01, 2015, 02:39:48 AM »
Really nice thanks for posting
Paul

Offline Glenn

  • Hero Member
  • *****
  • Posts: 507
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #16 on: August 01, 2015, 02:41:37 AM »
That is absolutely AWESOME !!!  You did a great job and I sure do appreciate you posting all these photos.  I've got plans in the future for a 16 gauge Trade Gun.  I'm going to log this thread for future use.  Thanks Again !!!
Many of them cried; "Me no Alamo - Me no Goliad", and for most of them these were the last words they spoke.

Offline elk killer

  • Hero Member
  • *****
  • Posts: 1489
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #17 on: August 01, 2015, 02:09:47 PM »
that's great,,
How long is it?
only flintlocks remain interesting..

Hemo

  • Guest
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #18 on: August 01, 2015, 03:29:37 PM »
Nice job, Curtis! Thanks for sharing this!

Gregg

Offline T*O*F

  • Hero Member
  • *****
  • Posts: 5076
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #19 on: August 01, 2015, 04:38:51 PM »
Curtis hasn't been at this all that long.  By profession, he's a technogeek, however he has acquired a lot of "life experience" along the way.  He built his own shop and then lived in it while he built his house.  The thing I respect most about him is his "can do" attitude.  He doesn't ask how to do something.  Instead, he figures it out on his own and then posts a "this is what I did and how I did it."

Others should take note of this.  The ability to think outside the box and accomplish something using only one's imagination, thought process, and problem solving skills is a rare thing.  He has no fear of failure.  Knowledge is gained thru experience.  To often others ask the most basic questions because they are afraid of making a mistake.  Things which they could easily figure out on their own.  Perhaps by emulating Curtis' attitude, they could become more proficient in what they attempt.  These are skills that are being lost in today's society.

Dave Kanger

If religion is opium for the masses, the internet is a crack, pixel-huffing orgy that deafens the brain, numbs the senses and scrambles our peer list to include every anonymous loser, twisted deviant, and freak as well as people we normally wouldn't give the time of day.
-S.M. Tomlinson

Offline Curtis

  • Hero Member
  • *****
  • Posts: 2184
  • Missouri
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #20 on: August 01, 2015, 08:44:26 PM »
Wow Dave, I guess all I can say to that is thanks for that most gracious review!  I can feel my head swelling already....  ;D

I do want to point out that I am not afraid to ask questions when I am stumped or figure there has to be a better way to do something.  Dave has been one of the people that has answered many of those questions over the past few years.  He is a very talented, primarily self taught builder that has tackled some very complex projects.

Also I just want to say I make a lot of mistakes when trying to figure things out, and folks should not be discouraged by their mistakes as they are often some of the most valuable learning tools for anyone.

Curtis
Curtis Allinson
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Sometimes, late at night when I am alone in the inner sanctum of my workshop and no one else can see, I sand things using only my fingers for backing

Offline BJH

  • Hero Member
  • *****
  • Posts: 1642
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #21 on: August 01, 2015, 11:36:20 PM »
Amen to learning from your mistakes. Every time I think I've made mostly all of them.... Suprise, here's a new one. Or worse yet, yup ya did it again. BJH
BJH

Offline Ed Wenger

  • Global Moderator
  • Hero Member
  • *
  • Posts: 2450
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #22 on: August 04, 2015, 04:55:17 AM »
I always enjoy your "how I did it" posts, Curtis!  Always learn something.  Thanks for posting the process, and nice engraving!


          Ed
Ed Wenger

Offline David Rase

  • Hero Member
  • *****
  • Posts: 4281
  • If we need it here, make it here. Charlie Daniels
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #23 on: August 04, 2015, 03:40:39 PM »
Great post and a just as great triggerguard.  Making as many parts for a rifle on your own that you can is always rewarding and many times humbling as you work through processes, techniques and jigs and fixtures.  I love seeing a piece of raw material transform into a functioning part as I work it through all its stages.
David

Offline Curtis

  • Hero Member
  • *****
  • Posts: 2184
  • Missouri
Re: Making a "Chiefs Grade" Trade gun Trigger guard
« Reply #24 on: August 05, 2015, 07:50:40 AM »
Thanks Dave and Ed!

that's great,,
How long is it?

elk killer, it was approx 10-3/4" when flat, 9 after finished (with the bow bent)

Curtis
Curtis Allinson
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Sometimes, late at night when I am alone in the inner sanctum of my workshop and no one else can see, I sand things using only my fingers for backing