« previous next »
Pages: [1]   Go Down

Author Topic: Old Time Turn Screw  (Read 3906 times)

Offline J Shingler

  • Full Member
  • ***
  • Posts: 196
Old Time Turn Screw
« on: August 17, 2022, 08:13:26 PM »
I needed a couple turnscrews for the shooting box.  Wanted something that looked better than a plastic handled Crafstman screwdriver. So I decided to make a couple sizes. One size fits the narrow top jaw and cock screw. The smaller one to fit the internal lock screws.  The brass ferrules are made from 45 ACP brass cases and 40 cal brass cases for the smaller size. Hand turned the handles on the lathe. Sanded a couple flats to keep them from rolling off a table or fit in a bag better. The turnscrew shanks are made from allen wrenches. Ground to size and heated and given a decorative twist. Turned out pretty good I think.







Logged
Thank you
Jeff

Offline rich pierce

  • Administrator
  • Hero Member
  • *
  • Posts: 19522
Re: Old Time Turn Screw
« Reply #1 on: August 17, 2022, 08:37:02 PM »
Pretty fine!
Logged
Andover, Vermont

Offline Grischi

  • Full Member
  • ***
  • Posts: 169
    • Youtube: 'Ist das Kunst oder kann das weg?'
Re: Old Time Turn Screw
« Reply #2 on: August 17, 2022, 09:08:23 PM »
They are awesome.
Logged

Offline smylee grouch

  • Hero Member
  • *****
  • Posts: 7907
Re: Old Time Turn Screw
« Reply #3 on: August 19, 2022, 05:11:11 AM »
Nice work. Gives me some ideas. Thanks ;)
Logged

Offline Brian Jordan

  • Hero Member
  • *****
  • Posts: 548
  • Pennsylvania
Re: Old Time Turn Screw
« Reply #4 on: August 19, 2022, 01:54:04 PM »
Nice work Jeff! You bringing any to Keating Mountain?
Logged
Elizabeth, PA

"No free man shall ever be debarred the use of arms"...Thomas Jefferson

Let's Go Brandon!

Offline jgraham1

  • Full Member
  • ***
  • Posts: 156
Re: Old Time Turn Screw
« Reply #5 on: August 19, 2022, 03:48:12 PM »
Beautiful work!

Jerry
Logged

Offline J Shingler

  • Full Member
  • ***
  • Posts: 196
Re: Old Time Turn Screw
« Reply #6 on: August 20, 2022, 08:28:54 PM »
Quote from: Brian Jordan on August 19, 2022, 01:54:04 PM
Nice work Jeff! You bringing any to Keating Mountain?

Not sure if I will have time to run any more before then. I should be th we re by Thurs.
Logged
Thank you
Jeff

Offline J Shingler

  • Full Member
  • ***
  • Posts: 196
Re: Old Time Turn Screw
« Reply #7 on: August 20, 2022, 08:32:20 PM »
Quote from: smylee grouch on August 19, 2022, 05:11:11 AM
Nice work. Gives me some ideas. Thanks ;)

Good that's what we are here for. Sharing ideas. Keep the end to be ground to the turnscrew bit clamped in the vice as a heat sink and you will not need to reharden and tempor.. Keep cool as you grind it of course.
Logged
Thank you
Jeff

Offline Greg Pennell

  • Hero Member
  • *****
  • Posts: 1522
Re: Old Time Turn Screw
« Reply #8 on: October 06, 2022, 06:01:36 AM »
Snazzy!
Logged
“Let your gun therefore be the constant companion of your walks” Thomas Jefferson

Offline flatsguide

  • Hero Member
  • *****
  • Posts: 853
Re: Old Time Turn Screw
« Reply #9 on: November 09, 2022, 03:31:07 PM »
Very nice! Neat ‘twist’ on the shank. Nice addition to any rifle or gun.
Cheers Richard
Logged

Paul_Brach

  • Guest
Re: Old Time Turn Screw
« Reply #10 on: November 24, 2022, 09:38:57 PM »
Really nice work!
Logged

Offline jgraham1

  • Full Member
  • ***
  • Posts: 156
Re: Old Time Turn Screw
« Reply #11 on: November 24, 2022, 10:02:46 PM »
Those would be great with a hex inset on the shaft to attach some of the Brownells bits.  Then you could have one handle and numerous bits for your rifle.

Jerry
Logged
Pages: [1]   Go Up
« previous next »